EMS Certification in Construction Management Systems | A2018

This article discusses the Environmental Management Systems Certification in the Construction Industry. It covers the critical processes, performance evaluation, and environmental analysis. It also includes the environmental aspects, stakeholders' requirements, and risk analysis.

49306 Quality and Operations Management Systems | Autumn
2018
Environmental Management Systems Certification in the
Construction Industry
Bonny w Munga
Faculty of Engineering and Information
Technology the
University of Technology Sydney
Date of Submission: 30 May, 2018

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
TABLE OF CONTENTS
List of
Tables…………………………………………………………………………………..3
List of
Figures………………………………………………………………………………….4
1. Executive
Summary…………………………………………………………………………5
2.
Introduction………………………………………………………………………………....
6
3. Environmental Management System (EMS)
Policy………………………………………….7
4. Stakeholders’ Requirements….
…………………………………………………………….9
4.1 Organisation
Stakeholders…………………………………………………………………………………
9
4.2 Organisation Stakeholders’
Needs…………………………………………………………………………………….....1
0
5. Performance
Evaluation…………………………………………………………………....12
5.1 Critical
Processes………………………………………………………………………………….12
5.2 Performance
Parameters…………………………………………………………
5.3 Methods to Evaluate Performance
Parameters……………………………………
6. Environment
Analysis……………………………………………………………………….
6.1 Environmental
Aspects…………………………………………………………
6.2 Environmental
Impacts……………………………………………………………
Page | 2 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
6.3 Environmental
Objectives………………………………………………………….
6.4 Environmental
Targets……………………………………………………………
6.5 Environmental
Actions…………………………………………………………
5.2 Methods to Measure and Monitor
Progress…………………………………….
7. Risk
Analysis……………………………………………………………………………….
7.1 Hazard
Identification………………………………………………………………
7.2 Risk
Assessment……………………………………………………………………
7.3 Risk Actions [Risk Treatment Plan]
……………………………………………….
8.
Conclusion………………………………………………………………………………….
References…………………………………………………………………………………
…
Appendix
A……………………………………………………………………………………
LIST OF TABLES
Page | 3 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
LIST OF FIGURES
Page | 4 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
5. PERFORMANCE EVALUATION
5.1 Critical Processes
The Strategic Operations Activities
ESCS Pty Ltd has identified the 10 strategic activities that steer it to the
attainment of its goals (Surowiecki, 2015). These are critical processes which
constitute the organization’s operations. The company focuses on management
of these strategic activities to survive the market turbulence, quality, and
environmental obligations. The success in the management of these key
processes propels the company to greater heights along its growth trajectory.
The key processes are:
1. Construction services (Australian Standards, 2018): The work provided by
the company for constructions purposes must serve the intended purpose,
be of the highest quality possible, and achieve the environmental
objective of the company. There must be consistency in costs, quality, and
resources across all the organization divisions.
2. Quality management: This involves creating satisfaction in both the
company and the outside stakeholders. The companies are expected to
meet the demands and expectations of the customers. The achieve this
the management does market research, to ascertain the customers’ needs
and also do quality assurance testing on products and services (Siva et al.,
2016).
Page | 5 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
3. Process and Capacity Design: It is the organization's responsibility to come
up with design strategies that fit all the production plans and goals
together with technology and resources required. There is a need for
keeping the value stream running efficiently by mapping them to
determine the necessary processes.
4. Location decisions: The management has the responsibility of determining
the most convenient and efficient location for organization’s operations
including receiving of supplies, the mobility of goods and services from the
company to the customers, and the location of choice for marketing and
public relations.
5. Layout Design and Strategy: The management must come with a strategy
for the design and layout of the desks, workstations, and the delivery and
usage of materials. This strategy will ensure smooth flow of operations
and organizational communications.
6. Human resources and job design: it is the responsibility of the
management to make human resource decisions and how jobs are
designed. The management makes continuous improvements programs
by training the workers, reviewing their responsibilities, and ensuring that
the workers are satisfied in their workplace so as to improve their
productivity (A. Idrus and M., 2012).
7. Supply chain management: The management must be thorough in
strategic streamlining, create cost-effectively and build trust with
stakeholders. This will ensure a smooth supply chain for the goods and
services.
8. Inventory control: The inventory control is the responsibility of the
management. Different clients’ specifications and needs bring inventory
challenges which call for better strategies and planning. Inventory
decisions are shaped by the weather, labour, and supply shortage.
9. Scheduling: This is a holistic approach to how operations are done in the
span of scheduled times. This includes how much time is required to
provide a satisfactory product and service to the customers and to
ascertain the number of machines required to perform any given
operations’ activities effectively.
10.Site and organization maintenance: This constitutes creating reliability of
machines and peoples. The maintenance process ensures every process is
running smoothly as per the plans of the organization, also ensure that no
runtime breakdowns.
The above ten-key operation processes are used as a guide to analyzing the operations of the
company. Coming up with strategies to operationalizing these ten areas in the organizational
decision-making process not only enhances the performance of the company but also fulfill
the environmental objectives.
5.2 Performance Parameters
Page | 6 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
Construction services: the company ranks its construction services in terms of
the revenue generated. This is how the customers demand the constructions
services. The company should also rank the poorest performing products in its
construction services which may have failed to resonate with the customers’
expectations or needs.
To monitor performance, the company needs to consider every specific context
that surrounds its products. This measure whether the product is gaining market
momentum through demand increase or if there is demand slump attributed to
the loss of popularity and competition.
The product performance may not always measure directly in the revenue
growth. Therefore, the company needs to come up with measures and metrics
that are consistent with the objectives and general model.
The following are the success indicators of the construction services of ESCS Pty
Ltd (Health Information and Quality Authority, 2013).
 A significant increase in revenue generated from construction services.
ESCS Pty Ltd deals with selling construction products and services which
are environmentally friendly and of high quality. An increase in the sales
revenue is attributed to the better performance of the company’s products
which is an indication that the product market is doing well in the market.
On the other hand, under-performing construction services are depicted
by low returns, stagnations, and market nonperformance
 A number of unit per order: The increase in the number of units per order
in an indicator of a performing product in the market, otherwise, the
product will be underperforming. A number of units per order are the
amount or value of the order placed by the customer with the company.
 Customer loyalty: This is all about attracting prospective customers,
convincing them to buy the product, have recurrent services orders,
increase their quantity of purchase and give referrals. To build customers
loyalty, customers’ needs and expectations must be addressed and
fulfilled. To measure customers loyalty the company conducts customers’
surveys, purchase feedbacks, and purchase analysis.
 Inventory size: The inventories in forms of raw materials, work-in-progress
and finished goods are the parts of the assets of the company. Inventory is
an important asset, and therefore the inventory turnover is considered
one of the primary sources of the company revenues. Growing company
put emphasis on management of neither inventory get too low nor too
much inventory. This includes forecasting the required inventory,
maintaining cost-effective lot sizes, and just-in-time delivery systems.
 The service quality: The Company provides engineering services and
products that fit the clients’ specifications. These services provided must
be of the intended quality in of the engineering perspectives. The services
and the products have to be durable while serving the intended purpose.
Tracking of construction services and products using above metrics is important
for varied reasons, but the most important is the culture performance
Page | 7 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
measurement. They measure to ensure the business is heading in the right
direction by evaluating the key indicators of performance.
Quality management: ESCS Pty Ltd has to ensure its constructions products and services
meet the required quality. In so doing, the main focus should be on the quality planning,
quality assurance, quality control and quality improvement in all its constructions operations
(Association for Project Management, 2018). The company should not only focus on the
product quality, but also on the means to achieve it.
It is at the disposal of the management to have performance metrics or performance
indicators on quality management (Health Information and Quality Authority, 2013). These
metrics are used to measure how the company is performing in matters quality of the
products and services.
The performance indicators include (Health Information and Quality Authority, 2013):
 Clients’ satisfaction and feedback (Shrivastava, 2016): ESCS Pty Ltd is not only
focusing on environmental sustainability but also clients focused. The construction
services seek to satisfy the customers’ needs, and therefore, the must meet the quality
thresholds. The company aims at building structures that are up to the clients’
specifications and needs. To measure this metric, the clients can fill the questionnaire
or the organization can conduct a survey.
 Employees’ satisfaction: A quality management process recognizes the need for
employees’ welfare and happiness of workplace. Satisfied workers are motivated to
perform their duties, and the out is high. It is the company’s responsibility to
continuously train workers, involve them in the organizational decision-making
processes and appraise them accordingly.
 The overall equipment effectiveness: This is the measure the availability of the
equipment needed for the production of services or product to the clients. It also
measures how these assets produce to their optimum levels. OEE also measures the
percentage of the services or products that are produced within the quality
specification. The problems with equipment and outage affect the efforts of quality
management.
 The percentage of the product or service compliance with the quality policy of the
company: This metric measures the quality of engineering sites and structures. This
ensures compliance with government regulations and guidelines on quality of
engineering structures and sites. It’s the responsibility of the company to improve on
production compliance of the services offerings.
 Timely completion and deliveries: Quality management should ensure on-time
completion of the order projects and deliveries but not at the expense of the service
and products quality. This metric measures the percentage of service or product the
company is able to deliver on time and complete free from errors and delays.
5.3 Methods to Evaluate Performance Parameters
Under this section, the company establishes the measurement methods for the
quality management and construction services. They include:
Page | 8 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
 Carrying out an employee survey: Employees can fill the questionnaire on
their work satisfaction and health and safety.
 Client satisfaction survey: The client can fill a confidential form stating
how service or the product of the company was. Also, state whether
he/she achieved the intended satisfaction.
 Projects audits: This is regularly checking on the completed or work in
progress p, to ascertain the quality of work being carried out by the
employees.
 Project evaluation questionnaires: The client fills the form after his/her
assessment of the project.
 Equipment monitoring: This ensures no downtimes for continuous
production.
6. ENVIRONMENT ANALYSIS
6.1 Environmental Aspects
These are the activities of the organizations that interact with the environment
and have an impact on the environments either directly or indirectly. It is the
duty of the company to control the magnitude of reduction in the environmental
impacts of these aspects. In the light of this, the following are the environmental
Page | 9 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
aspects that are involved in the construction services and management of
quality within and outside the company.
These include the following:
 Clearing of sites for constructions: Before any structure is elected,
according to the engineering designs, the site must be prepared by
cleared ready for construction. These involve removal of soils, any
vegetation, and levelling the ground. The act destroys the natural
aesthetic value that used to exist in the area
 Disposal of the excess soil and other ground materials: In the process of
clearing the field for construction, and excavation for foundation, loads of
soils are taken out. These soils need to be disposed from the site to create
space for construction. The company must have a means on how to
dispose of extra soil especially in a more conserving manner to the
environment.
 Drilling of boreholes: Water is needed to make concretes, for cooling, to
maintain the optimum moisture content of the new structure, human use,
etc. Sometimes it is convenient to drill boreholes for the supply of water
on the site. In as much as it seems convenient, boreholes are being
discouraged because there has been a proof that they create underground
hollows which result in adverse effects on the ground.
 Noise from machinery: The noise emanating from construction machinery
and vehicles is sometimes intense to the people operating them and those
within the precinct of the construction site. The noise is therefore likely to
cause nuisance thus noise pollution. The company is committed to
creating environmentally friendly working conditions for its workers and
the public.
 Vibrations: Huge machinery also cause vibration to the ground. These
vibrations when intense are likely to cause destructions of the soil
structure, buildings around, animals and people living near the site. One of
the adverse effects will occur because of fault line on building structures
which are catastrophic.
 Construction wastes: The site generates waste in the process of
construction. The waste needs to be disposed from the site to create
space for other operations. These wastes make the surrounding areas
unclean ugly. It is the responsibility of the company to clear them (Your
Guide to Environmental Management Systems, 2015).
 Cutting down of vegetation: In the process of building or construction site,
the company needs supporting pillars, and the most used are wood cut-
offs and timber. Also, during the clearing of the site trees are cut down to
pave a space for construction. This has led to deforestation and loss of
natural forests and vegetation.
 Dust from the construction activities: When constructing structures which
require soil excavation and transport, and use of concretes, dust is
produced. The blowing winds also increase the dust. As a result, it pollutes
the air.
Page | 10 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
 Excavation for the strong foundation: It is required that for strong
structures especially large structures, a good foundation is critical.
Excavation is therefore required for the foundation. Sometimes up to
100fts deep excavations are dug to create the foundation of a structure.
 Oil spillage: These are oil spillage from vehicles, and during handling of oil
containers and maintenance. These sip into the soil and later carried away
by the water runoff which has led to soil and water pollution. The company
has the responsibility to control this spillage or keeping it to the minimum.
6.2 Environmental Impacts
These are the anticipated effects of the project on the environment. These
impacts can be positive or negative, mild or adverse (Idrus and Napiah, 2012).
Therefore, it is the duty of the company to ensure that its operations.
Environmental aspects are well managed to eliminate or reduce the aggregate
environmental impact of a project. ESCS Pty Ltd is dedicated to providing
environmentally friendly products which aim at reducing the negative effects to
the environment.
These include the following impacts:
 Loss of the natural aesthetic values of the cleared site: As a result of land
clearing and destruction of vegetation and soil structure, the natural
beauty of the site is destroyed. Although most are the times when clearing
is necessary for development, there must be a way of restoring the beauty
back. This is done by planting flowers, grass, and ornamental trees around
the development.
 The disposed of soiled can be used to fill the open trenches and manholes:
The extra soil after clearing and excavations are carried to fill open
trenches and craters left by after mining. The soil is transported to areas
which have been polluted due to mining or soil erosion. It rehabilitates
these already polluted areas which later turn out to be productive land.
Disposing of this soil also creates a space for the construction site.
 Drilling of boreholes has been established to cause subsidence of the
earth: The studies have established that drilling of boreholes causes
subsidence of the ground. This phenomenon is explained using some
cracking of grounds, structures, and buildings. Also, it results in bending of
houses due to the loss of balance. Boreholes create underground hollows
which when large heavy structures are erected on the ground, tends to
shrink downwards causing ground subsidence and structures loss of
balance and bend.
 Noise pollution: The noise created by machines and vehicles become
nuisance thus causing noise pollution. The impact is the irritation to the
people working with them and the public living around the construction
site.
Page | 11 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
 Can cause faults lines on buildings and cause a nuisance to the people
living near the site: The heavy machinery causes mild earth tremors which
are a nuisance to the people living around the site. The intense vibrations
also cause a ground distraction which if intense can cause fault lines on
buildings and other big structures. The faults created can cause hazards
like corruption of the buildings and structures.
 Generation of wastes materials (Moreno, Font, and Conesa, 2016): The
construction process leads to the generation of wastes. The waste
constitutes of plastics, polythene, metal scraps, broken glasses, and
concrete blocks. If these wastes are left in the surrounding areas, it causes
the destruction of soil and even become hazardous to the community.
 Deforestation: Wood cut-offs, timbers and other constructions woods used
are as a result of cutting down trees. This has led to deforestation thus
loss of forest cover in the areas that the construction is established.
Deforestation is also caused by clearing the land for the preparation of
construction.
 Air pollution: Air pollution is caused by the dust from moving Lorries,
machines, and other operations in the site (Agarwal, 2005). These dusts
are carried by blowing winds to other areas. The dust can be harmful to
the workers and the public living near the construction site. It carries with
it construction chemicals and cement dust which pose a hazard to the
respiratory system.
 Underground land distractions: The excavation causes distraction of the
ground especially the crust for stability and underground waterways.
These distractions can result in the diversion of underground waters which
feed rivers. This land distraction may also cause landslides and subside
due to the weakened crust.
 Soil pollution: The oil spillages from the site cause soil pollution which is
detrimental to the vegetation. The oil spillage is caused by leakages from
maintenance of machines or accidents when handling oil containers. The
spillage is also the destruction of the ground animal life.
6.3 Environmental Objectives
These are the overall commitments of the company to make improvements on
the environment by reducing or eliminating the environmental impacts
completely. The company makes sure that the construction activities do not
impact negatively to the environments or if any negative impact it is reduced to
the minimum.
The objectives that the company is committed to achieving are:
 Restoring the lands natural values by planting trees around the
construction site: It is at the heart of the company’s objective and policies
to ensure environmental conservation and protection. Therefore, any
damage to the environment, the company is obligated to restore the
beauty of that land to the best way possible. The company aim at
Page | 12 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
recreating the areas through planting, flowers trees and covers
vegetation.
 Rehabilitation of the land: After excavation of the waste soil is found
useful by rehabilitating wastelands. This soil is transported to these lands
using trucks. The company aims at restoring the productivity of polluted
lands through filling them with soils. The soils disposals also allow more
space for the intended works.
 Look for alternative sources of water (Scarborough et al., 2015): The
Company will do away with drilling boreholes as the only source of water.
Instead, it will pump water from rivers or use piped water or use trucks to
draw water from the sources. The objective here is to eliminate the effects
that come with the drilling of boreholes. An alternative water source like
rivers is sustainable and cost-effective to the company.
 Reduction of noise to the minimum: The Company intends to reduce the
noise pollution by more than 20%. To reduce the noise means reducing
the amount of nuisance to the affected people especially workers and
those within the precinct of the construction site. It is the company policy
to minimize environmental pollutants to the minimum levels possible.
 Avoid high vibrations: The company aim at reducing the level of vibration
released to the environment. These vibrations cause earth tremors which
are distractions to the people, other animals, and the ground, therefore
avoiding them will reduce the effects on the environment. The company
intends to reduce this vibration to the minimum levels possible.
 Minimize waste materials: The operations that generate these wastes
need to be efficient and effective so as to minimize wastage. These
wastages are costs to the company because they must be cleaned and
disposed of well. Therefore, the company’s objective is to reduce the
amount of waste generated by the operations and keep them to the
minimum levels.
 Minimize deforestation and if trees are cut more are planted: Increase in
forest cover is important to achieve optimum climate. When it is
necessary to cut down the tree, the company will plant more to
compensate for the loss. But in ideally the company will reduce using tree
products in construction.
 Minimize the dust during constructions: The dust emanating from the
construction activities which include movement of vehicles and
machinery. Reducing the effects of these dust is critical. Therefore, ESCS
Pty Ltd is committed to reducing the amount of emission of dust to the air.
 Better approaches in the land excavation: The Company intends to use
better methods of creating the construction foundations. But when the
excavation becomes necessary, to the company must take any necessary
precautions in ensuring ground stability and strength, also must carry out
the due diligence during architectural planning and excavation.
 Reduce the soil pollutants: The company also aims at keeping the oil
spillage to the minimum or and eliminate incidences of spillage due to
handling. This will not only reduce soil pollution but will also reduce water
pollution resultant from runoff water into the rivers.
Page | 13 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
6.4 Environmental Targets
The targets are used to make achievements of the environmental objectives
easy by providing short-term goals. Each given objective can have various
achievable short-term targets which the company intends to fulfil in the span of
the project.
These objects target include:
 Restoration of the lands natural beauty by more than 60%: The Company
target to restore more than 60% beauty through the planting of a tree and
other vegetation. It is the objective of the ESCS Pty Ltd to reclaim lost
beauty of any land that it has caused damages to its natural beauty.
Failing to restore lands beauty makes land ugly and unattractive.
 Achieving total rehabilitation of the targeted land: The Company load
excess soil on trucks and deposit it to the polluted waste mining lands to
make them productive. The target is to rehabilitate as much land as
possible as long as there is extra soil that needs to be disposed of
appropriately. The reclaimed land can be utilized for other purposes like
farming of forestation. This will be a continuous process in every project
carried out.
 Exclude the option of drilling borehole as the source of water in the site:
The company has realized the negative effects that come from the drilling
of boreholes. Thus it intends to do away in the drilling of boreholes to
source for construction water. It intends to use piped water or use other
means to source water from the rivers in the next projects.
 Reducing the noise pollution by 20% in the next project: The nuisance
caused by machinery during when the work is in progress causes noise
pollution. The company aims at reducing this noise by 20% in the next
project. It will have to invest in on means for reducing noise pollution to
the minimum levels possible.
 Replace the machinery generating vibration by the next project: The
company objective is to reduce the amount of vibration caused by the
machinery. It targets to reduce vibration by 30%. This will require
investment in new machinery that generate low vibration in the
subsequent contracts.
 Aim to reduce the waste to the minimum levels: It is the purpose of the
company to reduce the waste because it also constitutes the overall cost
of production. Managing waste in the company is important as it helps to
keep it to the minimum.
 Reducing the rate of deforestation to the minimum: The Company intends
to conserve and improve the environment. Therefore, our intention is to
plant as many trees as possible. The company intends to replace the use
of wood with other substitutes like metal bars.
 Reduction of dust to the minimum levels: The dust emanating from
construction need to be contained to avoid air pollution and the effects to
Page | 14 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
the people. The company needs to employ methods on how to contain and
reduce the emission of dust to the air.
 Better planning in land excavation to avoid ground destructions: The
excavations have to be well planned to avoid adverse effects that might
turn to be hazardous to the people and pose a threat to the durability of
the structure.
 Eliminate the soil pollution: The oil spillage needs to be eliminated by
making sure handling processes are secure and no accidents to the oil
tanks. Repairs and maintenance should be done in a controlled
environment to avoid oil from spilling into the ground.
6.5 Environmental Actions
These are the company is ready and is prepared to do to ensure the
environmental impact is eliminated or reduced to the minimum. The actions
taken are in terms of the environmental objectives and targets of the company.
These are achievable actions that ESCS Pty Ltd plan to achieve environmental
objectives by enacting actions on them.
The following are the environmental actions which the company intends to take
to mitigate the conditions that arise in the process of its operations.
 Planting of various vegetation around the sites and building
environmentally friendly structures
 Filling of the open land with excess soil
 Sourcing of water from other sources like a river through piping or building
a dam for water storage
 Restriction of operation hours and use of soundproofed machines
 Replacement of machinery with one that produces mild vibration
 Recycling of such waste materials
 Planting trees on another set of land to replace the one felled
 Fencing of the round to reduce winds
 Prior analysis of the underground to ensure no underground phenomenon
will be destructed, for instance, underground waterways
 Ensure that no spillage of oils or any other soil contaminants
6.6 Methods to Measure and Monitor Progress
Monitoring implementation of the Environmental Action
Environment policy goes beyond the environmental aspects, impacts, objectives,
and targets; it also involves the monitoring implementation of the environmental
actions taken by the organization in ensuring environmental policy compliance,
controls, and mitigations. It is the company responsible, therefore, to regularly
monitor the actions undertaken in environmental conservations and control.
Page | 15 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
They include:
 Regular audit of the actions: The Company needs to use audits as an
essential way of getting the feedback on the environmental management
system, rules regulations and quality standards. To conduct the
environmental audit, the company needs to conduct surprise visits to the
site. The audit covers everything relating to the environmental aspects
which have been covered in this text like excavation, oil spillage,
deforestation, land clearing, and noise.
 Continuous feedback from the stakeholders: The Company needs to be
getting continuous feedback from the customers and workers and also the
public to know what is happening in the construction site, how workers
are performing, and the effects of the project to the environment and the
public. This practice also assists the company to come up with the
solutions to the challenges it faces.
 Carrying out the survey: The management is required to do regular
surveys to ascertain the extent to which the company’s operations are
impacting on the environment. The survey can take the form of a
questionnaire or random interviews with the employees and other
stakeholders. To findings are then used to make the environmental
policies and decisions.
 Regular inspections and follow-ups: The company carries out regular
inspections of the structures and equipment to ascertain their
performance and their reliability. The company equipment needs to be
working correctly after every task completed. Therefore they should be
checked after each job to ensure that they are working properly for the
next task. Also, regular check-ups are important to ensure that hazards
are avoided due to emissions and pollution on the environment.
 Safety assessments (Violante, 2018): The company intends to ensure the
health and safety of the workers. This is achieved through adherence to
the rules and regulations affected by the government legislation. The
working condition of the workers is critical for their performance. Safety
also ensures the safety of the public. Proper audits should be random and
unexpected to measure the preparedness of the operations in terms of
health and safety.
Page | 16 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
REFERENCES
Agarwal, S. 2005, Air pollution, 1st ed., A.P.H. Publ., New Delhi
Association for Project Management 2018, Introduction to quality management.
Association for Project Management, viewed 29th May 2018,
<https://www.apm.org.uk/body-of-knowledge/delivery/quality-management/>
Australian Standards. 2018, SAI Global, 1st ed.
Gallo, C., Faccilongo, N. & La Sala, P. 2018, ‘Clustering analysis of environmental
emissions: A study on Kyoto Protocol's impact on member countries’, Journal of
Cleaner Production, 172, pp.3685-3703.
Health Information and Quality Authority 2013, ‘Guidance on Developing Key
Performance Indicators and Minimum Data Sets to Monitor Healthcare Quality’,
Dublin: Health Information and Quality Authority, pp.13-24.
Idrus, A., O., & M., N. 2012, ‘Human resource management in the construction of
a sustainable development project: towards successful completion’, Universiti
Teknologi Petronas, Perak, Malaysia.
Idrus, O. & Napiah, M. 2012, Environmental Impact, WIT Press, Perak, pp.169-
180, viewed 29th May 2018, <https://www.witpress.com/>
Moreno, A., Font, R., & Conesa, J. 2016, ‘Physical and chemical evaluation of
furniture waste briquettes’, Waste Management, 49, pp.245-252.
Page | 17 of 71

 ESCS Pty Ltd
2018
EMS Certification in Construction 49306 Quality and Operations
Management Systems | A2018
Scarborough, H., Sahin, O., Porter, M., & Stewart, R. 2015, ‘Long-term water
supply planning in an Australian coastal city: Dams or desalination?’,
Desalination, 358, pp.61-68.
Shrivastava, P. 2016, House of quality: an effective approach to achieve
customer satisfaction & business growth in industries, 1(1), pp.1-2.
Siva, V., Gremyr, I., Bergquist, B., Garvare, R., Zobel, T. & Isaksson, R. 2016, ‘The
support of Quality Management to sustainable development: a literature review’,
Journal of Cleaner Production, 138, pp.6-7.
Surowiecki, J. 2015, The environmental legacy of the Volkswagen scandal, The
New Yorker, viewed 29th May 2018, <http://www.newyorker.com/news/daily-
comment/the-environmental-legacy-of-the-volkswagen-scandal>
Violante, A. 2018, ‘Risk management in construction projects: Are Small
Companies Prepared?’, MOJ Civil Engineering, 4(1).
Your Guide to Environmental Management Systems 2015, Oxon: Waste &
Resources Action Programme, 1st ed., pp.2-10,25-33, viewed 29th May 2018,
<http://www.wrap.org.uk/sites/files/wrap/WRAP%20EMS%20guide
%20Mar2015.pdf>
Page | 18 of 71