Setting Up Network Services

This assignment details the process of setting up various network services. It covers configuring web servers by entering IP addresses into a browser, establishing DNS services with specific names and IP addresses, and implementing firewall rules to control TCP traffic. The instructions emphasize using graphical interfaces to manage these services.

internetworking with tcp/ip

Table of Contents
1. Project Objective.................................................................................................................1
2. Network Setup Requirements.............................................................................................2
3. Network setting...................................................................................................................2
3.1 Device Setup................................................................................................................2
3.1.1 PC setup...............................................................................................................2
3.1.2 Server setup..........................................................................................................8
3.1.3 Switch Setup.......................................................................................................11
3.1.4 Router Setup.......................................................................................................14
3.2 Network Diagran.......................................................................................................17
3.3 IP route......................................................................................................................18
3.4 Ping............................................................................................................................21
3.5 Trace Route Command..............................................................................................23
4. Network services...............................................................................................................25
4.1 DHCP services...........................................................................................................25
4.2 Web services..............................................................................................................27
4.3 DNS service...............................................................................................................28
4.4 Firewall services........................................................................................................33
References................................................................................................................................35
1. Project Objective
Objective of this project is to set up the simple network. It contains the more than two
routers, switches, server and personal computers. The network setup will be done by using
the cisco packet tracer. The cisco packet tracer is the one of network simulator. It provides
1

the high effective network setup. The Network setup using the cisco products such as cisco
routers, switches and server. The Routers are connected with the Switches. The Switches are
connecting the two personal PC ‘s and server. The network setup using the three servers.
Because the network services are done by using the server. The network services are DNS,
firewall, Web and DHCP services. These services re will be configured.
2. Network Setup Requirements
The network setup hardware requirements are shown below.
 Cisco Routers - 3
 Cisco Switches - 3
 Cisco Server - 3
 Personal Computer - 6
 Operating System - Windows 7
 Hard Drive - 2.4 GB
 Memory - 2 GB RAM
3. Network setting
The simple network divided into two steps such as (Introduction to networks, n.d.),
 Device setup
 Network services configuration
These are discussed in detail.
3.1 Device Setup
The device setup includes the four main steps such as,
 PC setup
 Switch setup
 Server setup
 Router setup
These are shown below.
3.1.1 PC setup
To setup the PC by click the PC and choose the Desktop to select the IP
configuration.
In PC 0,
2

Enter the IP address as 192.168.1.10, subnet mask as 255.255.255.0 and default gateway as
192.168.1.1. It is displayed in below (NETworking, 2013).
In PC 1,
Enter the IP address as 192.168.1.11, subnet mask as 255.255.255.0 and default gateway as
192.168.1.1. It is displayed in below.
3

In PC 3,
Enter the IP address as 192.168.2.10, subnet mask as 255.255.255.0 and default gateway as
192.168.2.1. It is displayed in below (Packet tracer, 2012).
4

In PC 4,
Enter the IP address as 192.168.2.11, subnet mask as 255.255.255.0 and default gateway as
192.168.2.1. It is displayed in below.
5

In PC 5,
Enter the IP address as 192.168.3.10, subnet mask as 255.255.255.0 and default gateway as
192.168.3.1. It is displayed in below (Jesin, 2014).
6

In PC 2,
Enter the IP address as 192.168.3.11, subnet mask as 255.255.255.0 and default gateway as
192.168.3.1. It is displayed in below (Scaling networks companion guide, n.d.).
7

3.1.2 Server setup
To setup the server by click the server and select the desktop to choose the IP configuration.
In Server 0,
Enter the IP address as 192.168.1.12
Subnet mask as 255.255.255.0
Default gateway as 192.168.1.1
It is shown in below.
8

In Server 1,
Enter the IP address as 192.168.2.12
Subnet mask as 255.255.255.0
Default gateway as 192.168.2.1
It is shown in below (Connecting networks companion guide, 2014).
9

In Server 1,
Enter the IP address as 192.168.3.12
Subnet mask as 255.255.255.0
Default gateway as 192.168.3.1
It is shown in below.
10

3.1.3 Switch Setup
To setup the switch by click the switch.
Enter the below command in the command line interface. It is shown in below.
11

12

13

3.1.4 Router Setup
To setup the router by click the router.
Enter the interface information and set the IP address for the router.
For Router 0,
Enter the Interface as fa0/1
IP address as 192.168.1.1
Subnet mask as 255.255.255.0
Another Interface as se2/0
IP address as 30.0.0.1
Clock rate 64000
Subnet mask as 255.255.255.0
It is shown in below (Kenyon, 2002).
14

For Router 1,
Enter the Interface as fa1/0
IP address as 192.168.2.1
Subnet mask as 255.255.255.0
Interface as se2/0
IP address as 30.0.0.2
Subnet mask as 255.255.255.0
Interface as se3/0
IP address as 50.0.0.1
Subnet mask as 255.255.255.0
15

It is shown in below (Oppenheimer, 2011).
For Router 2,
Enter the Interface as fa0/0
IP address as 192.168.3.1
Subnet mask as 255.255.255.0
Interface as se2/0
IP address as 50.0.0.2
Subnet mask as 255.255.255.0
It is shown in below.
16

3.2 Network Diagram
The simple network diagram is shown below. It is done by using the cisco packet tracer.
The Simple network setup includes the router, switch, server and PC setup. These are
configured. It is shown in the network diagram.
In network diagram, the routers are connecting the swtiches. The swtiches are connected
with the PC and server. These are interconnecting with each other by using the IP routing
methdologies and inter VLAN network (Comer, 2014).
Here using the three separate the server for the network services. The network services re
DHCP, Web and DNS services. These are communicate each other. It is shown in below.
17

The Cisco file is attched here.
3.3 IP route
The simple network using the IP routing to interconnecting the routers. The IP routing is fully
implement, operated and managed by the routers.
In Router 0,
To do the IP router by Enter the below command in the command line interface,
ip route 192.168.2.0 255.255.255.0 192.168.1.0
It is shown in below (Miller, 2008).
18

In Router 1,
To do the IP router by Enter the below command in the command line interface,
ip route 192.168.1.0 255.255.255.0 192.168.2.0
ip route 192.168.3.0 255.255.255.0 192.168.2.0
It is shown in below.
19

In Router 2,
To do the IP router by Enter the below command in the command line interface,
ip route 192.168.2.0 255.255.255.0 192.168.3.0
It is shown in below.
20

3.4 Ping
The client pings the own interface. It is shown in below.
21

The client pings the server interface. It is shown in below.
22

3.5 Trace Route Command
The network setup some time having the network issues. So, to identify the network
trouble shootin problems by using the trace route command. The trace route command is
based on command line interface. It using the one or more trace route utility. Here using the
tracert utility. It is shown in below (Learning network services for professional development,
2014).
23

24

4. Network services
In simple network contains the more than one network services. These are listed below.
 DHCP services
 DNS services
 Web services
 Firewall services
These are discussed in detail.
4.1 DHCP services
To setup the DHCP service by click the DHCP server and select the services to choose the
DHCP services (Hunt, 2010).
In DHCP services window,
Click the Service on button.
25

After enter the pool name as 192.168.1.0
Default gateway as 192.168.1.1
Start IP address as 192.1681.1.10
Subnet mask as 255.255.255.0
Finally, add and save the services.
It is shown in below.
26

To check the DHCP connection by click the PC and Choose the DHCP. It provides
the IP address for the PC. It is shown in below (Donahoo & Calvert, 2009).
4.2 Web services
To setup the web services by click the web server and click the web browser. Enter the
IP address in the web browser URL. It is shown in below (Wood, 2006).
27

4.3 DNS service
To setup the DNS service by click the DNS server and select the services to choose the DNS
service.
In DNS service window,
Click the DNS service ON button.
After enter the name as www.csu.edu.au
IP address as 192.168.4.0
Finally, save and add the service.
It is shown in below (Mehta, 2013).
28

Then allow the NAT address in the interface for outside and inside of the router. It is shown
in below.
29

30

31

The DNS service is shown below.
32

4.4 Firewall services
To setup the firewall service by click the server and choose the Firewall.
In Firewall window,
Click the Firewall service ON button (Hollar & Murphy, 2006).
Choose them
Action as Allow
Protocol as TCP
Enter the,
IP address as 192.0.0.0
Wildcard Mask as 0.255.255.255.
Finally, save and add the service. It is shown in below.
33

The firewall service is used to blocks the TCP network traffic between the client and server.
It is shown in below.
34

References
Comer, D. (2014). Internetworking with TCP/IP. Boston, Mass.: Pearson.
Connecting networks companion guide. (2014). Indianapolis, IN.
Donahoo, M., & Calvert, K. (2009). TCP/IP sockets in C. Amsterdam: Morgan Kaufmann.
Hollar, R., & Murphy, R. (2006). Enterprise Web services security. Hingham, Mass.: Charles
River Media.
Hunt, C. (2010). TCP/IP Network Administration. Sebastopol: O'Reilly Media, Inc.
Introduction to networks.
Jesin, A. (2014). Packet Tracer Network Simulator. Birmingham: Packt Publishing.
Kenyon, T. (2002). High-performance data network design. Boston: Digital Press.
Learning network services for professional development. (2014). [Place of publication not
identified].
Mehta, V. (2013). Icinga Network Monitoring. Packt Publishing.
Miller, M. (2008). Wireless networking with Microsoft Windows Vista. Indianapolis, Ind.:
Que.
NETworking. (2013). [Hong Kong].
Oppenheimer, P. (2011). Top-down network design. Indianapolis, Ind.: Cisco Press.
Packet tracer. (2012). [Place of publication not identified].
Scaling networks companion guide.
Wood, R. (2006). Next-generation network services. Indianapolis, Ind.: Cisco Press.
35