Passive Optical Analyzer Project at University Tun Hussein Onn, Malaysia
Added on 2023-06-04
8 Pages1640 Words381 Views
CE 1.1 Project Information
Name of the project: Passive Optical Analyzer
Location of the project: University Tun Hussein Onn, Malaysia
Project Duration: Please fill
Organization: University Tun Hussein Onn, Malaysia
Role and Designation during the time: Chief Project Developer
CE 1.2 Project Background
CE 1.2.1 Characteristics of the project
The passive optical network or PON is the type of fibre optic access network that
allows downstream signals to broadcast in each and every premise and to share the several
fibres. During this project, I have designed an optical network analyser for the purpose of
analysing the passive optical network. I had to implement the point to multipoint architecture,
where I unpowered the fibre optical splitters and then enabled the single optical fibre for
serving the multiple end points. Since, there are several versions of passive optical network, I
had to select the most suitable version for providing a better result to my project. Being an
electronics engineer, I selected the final version of ITU T G.983 standard on the basis of
ATM or Asynchronous Transfer Mode. I took the APON/ BPON that provided 622 Mbit/sec
or megabits per second of the downstream bandwidth as well as 155 megabits per second of
the upstream bandwidth. Therefore, in this project, I have successfully developed the
compact design of the passive optical analyser and increase the overall performance of the
optical communications by using OptiSystem 12.0 simulation program.
Name of the project: Passive Optical Analyzer
Location of the project: University Tun Hussein Onn, Malaysia
Project Duration: Please fill
Organization: University Tun Hussein Onn, Malaysia
Role and Designation during the time: Chief Project Developer
CE 1.2 Project Background
CE 1.2.1 Characteristics of the project
The passive optical network or PON is the type of fibre optic access network that
allows downstream signals to broadcast in each and every premise and to share the several
fibres. During this project, I have designed an optical network analyser for the purpose of
analysing the passive optical network. I had to implement the point to multipoint architecture,
where I unpowered the fibre optical splitters and then enabled the single optical fibre for
serving the multiple end points. Since, there are several versions of passive optical network, I
had to select the most suitable version for providing a better result to my project. Being an
electronics engineer, I selected the final version of ITU T G.983 standard on the basis of
ATM or Asynchronous Transfer Mode. I took the APON/ BPON that provided 622 Mbit/sec
or megabits per second of the downstream bandwidth as well as 155 megabits per second of
the upstream bandwidth. Therefore, in this project, I have successfully developed the
compact design of the passive optical analyser and increase the overall performance of the
optical communications by using OptiSystem 12.0 simulation program.
CE 1.2.2 Objectives developed for the project
In the project of Passive Optical Analyser, I had to use technologies like FTTH and
PON for getting accurate results. I had used OptiSystem 12.0 simulation program for
analysing the PONs as well as calculation of power budget. I even had compared my results
with the desired theoretical output. My main objective was to provide a design for my passive
optical analyser. Hence, to complete this project with better efficiency or priority, following
objectives were developed by me.
To provide a compact design of passive optical analyzer for getting accurate results.
To increment the overall presentation of the optical communication with any specific
passive optical network.
To utilize OptiSystem 12.0 simulation program for calculating the power budget
theoretically.
To maintain the compatibility of passive optical networks and calculated power
budget.
To analyze the overall effect of the electro optical components by Bit Error Rate or
BER diagrams.
To analyze the respective spectrum outputs and time domain for checking the effect
of electro optical components.
To compare and contrast the practical results with my desired outputs.
CE 1.2.3 My area of work
I was appointed as the chief project developer in the project. I had enough field
experience for any type of electronics project and even bear core knowledge in electronics
engineering; hence I was selected to complete my project with my three other team members
under the guidance of my project leader. I had basic knowledge of logic designing, analog
and digital communication and thus completing this project was much easier for me. My
In the project of Passive Optical Analyser, I had to use technologies like FTTH and
PON for getting accurate results. I had used OptiSystem 12.0 simulation program for
analysing the PONs as well as calculation of power budget. I even had compared my results
with the desired theoretical output. My main objective was to provide a design for my passive
optical analyser. Hence, to complete this project with better efficiency or priority, following
objectives were developed by me.
To provide a compact design of passive optical analyzer for getting accurate results.
To increment the overall presentation of the optical communication with any specific
passive optical network.
To utilize OptiSystem 12.0 simulation program for calculating the power budget
theoretically.
To maintain the compatibility of passive optical networks and calculated power
budget.
To analyze the overall effect of the electro optical components by Bit Error Rate or
BER diagrams.
To analyze the respective spectrum outputs and time domain for checking the effect
of electro optical components.
To compare and contrast the practical results with my desired outputs.
CE 1.2.3 My area of work
I was appointed as the chief project developer in the project. I had enough field
experience for any type of electronics project and even bear core knowledge in electronics
engineering; hence I was selected to complete my project with my three other team members
under the guidance of my project leader. I had basic knowledge of logic designing, analog
and digital communication and thus completing this project was much easier for me. My
Project Supervisor
Team Member Team Member Chief Project
Developer (Me)
Team Member
main area of work was to propose a compact design for this passive optical analyser. I was
hence selected as the chief project developer for guiding the other team members and
checking the project progress properly.
CE 1.2.4 Project Group
Figure 1: People involved in the project
CE 1.2.5 My responsibilities throughout the project
As the chief project developer in the project of PON, I subsequently had some of the
most significant responsibilities like designing the passive optical analyser and providing
accurate results. I had to utilize FTTH or fibre to the home and passive optical network
technologies for the purpose of reducing significant expenses and then analysing optical
communications. My other responsibility comprised of checking efficiency of ONU or
optical network unit as well as OLT or optical line termination within the passive optical
network. I also used OptiSystem 12.0 simulation program for analysing the several
applications of PON and then interpreted my results subsequently. I even analysed electro
Team Member Team Member Chief Project
Developer (Me)
Team Member
main area of work was to propose a compact design for this passive optical analyser. I was
hence selected as the chief project developer for guiding the other team members and
checking the project progress properly.
CE 1.2.4 Project Group
Figure 1: People involved in the project
CE 1.2.5 My responsibilities throughout the project
As the chief project developer in the project of PON, I subsequently had some of the
most significant responsibilities like designing the passive optical analyser and providing
accurate results. I had to utilize FTTH or fibre to the home and passive optical network
technologies for the purpose of reducing significant expenses and then analysing optical
communications. My other responsibility comprised of checking efficiency of ONU or
optical network unit as well as OLT or optical line termination within the passive optical
network. I also used OptiSystem 12.0 simulation program for analysing the several
applications of PON and then interpreted my results subsequently. I even analysed electro
End of preview
Want to access all the pages? Upload your documents or become a member.
Related Documents
Summary Statement for Professional Engineering Competency Element PE 1lg...
|8
|1221
|338
Project: Deployment of GPON and Commissioning of FDHlg...
|8
|1692
|157