Network Configuration and Routing Protocol Implementation Report

This assignment report details the network configuration for ABC Company, addressing IP addressing, subnetting, and routing protocol implementation. The solution begins by defining the network parameters for NET-A, NET-B, and NET-C branches, including network addresses, broadcast addresses, and valid host ranges. It includes a table with IP addresses for each device interface and gateway configuration. The report then provides the configuration commands for routers RA, RB, and RC, covering interface setup and the enabling of a routing protocol (RIP). The configuration steps are shown for each router, demonstrating the setup of interfaces and the application of the selected routing protocol. The assignment fulfills the requirements of analyzing and proposing a new network configuration based on the provided network diagram and student ID-based network parameters.

Running head: - NETWORK CONFIGURATION
NETWORK CONFIGURATION
Name of the Student
Name of the University
Author Note

1NETWORK CONFIGURATION
Table of Contents
1. Task-A:...................................................................................................................................2

2NETWORK CONFIGURATION
1. Task-A:
NET-A
Network/Subnet _ 10.10.140.0/24 ___________________________
Network address__ 10.10.140.0 _____________________________
Broadcast address__ 10.10.140.255 __________________________
Valid Host Range __ 10.10.140.1 - 10.10.140.254 ______________
This provides the details of the entire NET-A branch along with the server and the two hosts
connected to the branch.
NET-B
Network/Subnet _ 172.16.140.0/24 ____________________________
Network address___ 172.16.140.0 ______________________________
Broadcast address__ 172.16.140.255 ____________________________
Valid host range____ 172.16.140.1 - 172.16.140.254 ______________

3NETWORK CONFIGURATION
This provides the details of entire Net-B branch along with the configuration of both the hosts
connected to this branch.
NET-C
Network/Subnet _ 192.168.140.0/24 ___________________________
Network address___ 192.168.140.0 _____________________________
Broadcast address__ 192.168.140.255 ___________________________
Valid host range____ 192.168.140.1-192.168.140.254 ______________
This provides the details of the entire Net-C along with the two hosts and the two servers
connected to the branch.
RA - RB subnet ____255.255.255.0 ____________________________
RB - RC subnet ____ 255.255.0.0 ______________________________
Net A subnet mask __ /24 ____________________________________
Fill the following table with the corresponding IP addresses:
Device Interface IP Address/ Subnet Mask D/Gateway
RA
Fa0/0 10.10.140.0/24 To NET A
S0/0/0 10.10.10.1/24 TO RB
RB S0/0/0 10.10.10.2/24 TO RA
S0/0/1 10.10.10.3/24 TO RC
RC Fa0/0 172.16.140.0/24 To NET B

4NETWORK CONFIGURATION
Fa0/1 192.168.140.0/24 To NET C
Configure router RA interfaces
RA(config)#:____ int F0/0 ______________________________________
RA(config-if)#: __ ip address 10.10.140.1 255.255.255.254 ___________
RA(config-if)#:___ exit _________________________________________
RA(config)#:_____ int S0/0/0 ____________________________________
RA(config-if)#:__ ip address _ 10.10.10.1 255.255.255.1 _____________
RA(config-if)#:___ exit _________________________________________
The above commands show the configuration for the first router named RA.
Configure Routing Protocol
1. Provide commands to enable any routing protocol (student’s choice) in RA)?
RA(config)#:_____ router rip ____________________________________
RA(config router)#:_ network _ 10.10.10.1 __________________________________
RA(config-router)#:_ network _ 10.10.140.1 ____________________________
RA(config-router)#:_ exit __________________________________
This shows the routing protocol for the first router named A.
2. Provide commands to enable routing protocol in RB (same protocol configured in
RA)? RB(config)#:___ router rip
_________________________________________________

5NETWORK CONFIGURATION
RB(config-router)#:__ network 10.10.10.2
_______________________________________
RB(config-router)#:___ network 10.10.10.3 _____________________________________
RB(config-router)#:___ exit _____________________________________
This shows the routing protocol for the second router named RB.
3. Provide commands to enable routing protocol in RC (same protocol configured in
RA)?
RC(config)#:__ router rip ________________________________________________
RC(config-router)#:_ network 10.10.10.3 _______________________________________
RC(config-router)#:_ network 192.168.140.0
_____________________________________ RC(config-router)#:__ exit
_____________________________________________
This shows the configuration of the routing protocol for the third router named RC.